Features

Lehman loader selling point:
Mountain one Reiman, fuel efficient, good car model.

First,Basic model configuration:
Axle, gearbox, engine, power, tires, loading height, bucket width...

Second,practicality:
1, the use of rubber pipeline and metal pipeline combined distributed pipeline, to ensure that the hydraulic oil flow is better, the rise of greater force.
2, the whole vehicle adopts 4:6 golden ratio, balance the weight ratio of the front and back under the working state, avoid the problem of the shovel process of the vehicle, the front end is too heavy after the rollover; Reasonable frame hinged opening Angle, so that the turning radius is smaller.
3, the counterweight through the double side height design, so that the vehicle steering process, effectively protect the rear hood, concrete filling counterweight so that the shovel loading process before and after the weight balance, higher safety factor.
4, The transmission fuel filler is extended, which is convenient for later maintenance.

Third,Economy:
1, gearbox and axle use the latest speed ratio, the vehicle speed is faster.
2, the working gear supports the second gear work, improve the working efficiency.
3, compared with the same type of engine, has a longer engine stroke, higher thermal efficiency, fuel saving 20%.
4, the vehicle painting using electroplating process, to solve the paint surface fading, rust problems, higher retention rate.
5, the vehicle pipeline layout, reduce tubing wear, increase tubing life, reduce maintenance costs.

Fourth,security:
1, The pin adopts spline self-locking nut to ensure that the pin does not fall off; All screws are self-locking nuts to improve safety.
2, diesel/hydraulic tank equipped with thermometer, prevent high temperature convenient and practical.
3, the rear hood adopts the frame structure, strong and durable without deformation, and the double wing side door is open for easy maintenance.

Five,comfort:
1, cab aviation seat, strong packaging, high comfort, high back support, long time operation is not easy to fatigue.
2, cab gear rational design, improve the ease of operation.
3, cab and engine foot pad, using high elastic rubber pad, reduce vibration, better comfort.
4, one stamping cab, sound insulation and noise reduction.

Technical Parameter

Diesel Engine	Equipment Hydraulic system：
Model: YN38GBZ	Cab：
Spray: direct injection, mechanical control	Maintenance and Oil filling:
Maximum power: 76 kW (103 horsepower)	The loading arm can be equipped with an automatic weighing sensor, which is double acting on the lifting and resetting oil cylinders of the device. The manually controlled feeding port has a standard prompt function
Total displacement - number of cylinders: 3860 milliliters -4-cylinder inline	Total capacity of hydraulic system: 107 liters
Cooling: water-cooled, dry air filter	Provide 1 chute extension component as standard configuration
Maximum torque: 340 Nm 1800 rpm	Capacity: 0.56m ³ Loading times required for each fill: approximately 4 times
Electric System:	Maximum flow rate: 40/63 liters/minute
Generator: 28V-750WA 100AH(550A)	4-piece multifunctional joystick
Battery: 2*12V-60AH(272A)	The rotation of the drum is achieved through the cycloidal hydraulic motor of the open oil circuit of the gear pump, and there are manual control valves in the operating room and at the rear of the mixer
Steering:	Fuel tank: 107 liters
Two wheel steering, assisted by a dual displacement load sensing power steering system on both steering wheels. Articulated steering.	Weight:
4*4 Four-Wheel Drive：	Geometric capacity of drum: 3200 liters Extension: 3213 liters
Hydraulic torque converter gearbox, open hydraulic gear oil pump, reverse gear control device. Control "working speed" and "moving speed"	Double pipeline, two return oil filters, open inlet oil, hydraulic oil filter can be replaced from the outside
Speed:	The enclosed operating room can be equipped with a heating/cooling system and a sloping front window. Humanized seats, equipped with flexible suspension and height adjustment function
Two forward gears and two reverse gears, high and low speeds	Oil: 10 liters
High speed first gear: 0-113.8 kilometers per hour Second gear: 0-26.9 kilometers per hour	Aluminum heat exchanger, used for cooling hydraulic oil. Temperature controlled control 55 ° automatic opening of hydraulic cooling device
Low end first gear: 0-5.1 kilometers per hour Second gear: 0-10 kilometers per hour	Loading:
Axle and Tyre:	Drum rotation speed: 18 revolutions per minute
"The front and rear axles are specially designed with large four-wheel clamp reduction axles and flange connected transmissions. Rear axle swing up and down (± 10 °) Tires: 750-16 front four wheels, rear 12-16.5"	The double conical drum has a double spiral stirring screw and a convex bottom
Brakes:	The unloading chute is controlled by a manually adjustable handle to tilt
External disc brake and emergency brake, applied to 4 wheels, dual circuit air brake, air cut hand brake	Maximum pressure: 20MPa megapascals
Water system:	Operating weight: 6160kg
Two sets of water supply systems, large diameter submersible pumps. Water is directly injected into the drum through the water tank. The total capacity of the water tank is 1030 liters. Visual flow meter, manual control of steam drum inlet water volume	Maximum total weight: 11600kg
Mixing and Unloading:	Maximum load capacity: 5000kg

Process

Technology Support

• 

  Construction Cases

• 

  Dealers Network

• 

  Technical Support